The structure is reasonable, the braking force is large, and the plug-in connection method of the support arm and the braking rail is simple to install and easy to repair and reset.
The basic model is: CDH-C-plug-in sliding car stopper, suitable for standard rail railway vehicles, the height of the center of the buffer seat from the rail surface is 850mm.
The geometric shape of the buffer seat and the height of the center distance from the rail surface of the vehicle stopper match the geometry of the brake coupler and the height of the center distance from the rail surface. The width of the main body frame corresponds to the gauge of the track, forming a series of products. But it is used for various vehicles of standard rail, wide rail, narrow rail and urban rail transit.
The meaning is as follows:
|Wide rail||Narrow gauge||Light Rail||subway||City fast|
|12th place||Impact speed km / h (divided into 10, 15, 20, 25, 28, etc.)|
|456th||Height of bearing center from rail surface mm|
Cushion rubber sheet
The impact force of the vehicle is transmitted to the brake rail by the buffer rubber plate and the left and right arms of the support.
Brake rail, spring seat. Friction resistance with basic rail prevents vehicle from sliding
It is composed of leaf spring, spring seat, wedge iron and bearing seat. It is installed in the brake rail and booster brake rail of the main frame. Its role is to form a pre-pressure when the vehicle stopper is static and increase. Friction resistance during braking, and can make the braking force continue to work in dynamic until stopping.
The arm plate is made of a whole plate, and the main frame is composed of the support, the front and rear beams, and the upper and lower oblique beams. The structure is reasonable, the whole is strong, and it can withstand the impact of the vehicle at high speed.
The arm plate is directly inserted into the brake rail by the lower hoof block. The structure is simple, and the installation, maintenance and reset are convenient.
After the main frame is stressed, the two pairs of brake rails in front of the stopper, the two rear pairs of brake rails, and the two pairs of boosters slide in order, and the frictional resistance gradually increases, which can prevent the vehicle and the main frame from being damaged, and can also block the vehicle Device cumulative resistance increases. Has a large braking capacity.
|Structural strength allows maximum impact speed v and energy height h|
|3rd gear||CDH-C20||v = 20 km / h||h = 1.57m|
|4th gear||CDH-C25||v = 25 km / h||h = 2.46m|
|Total horizontal resistance when sliding|
|1st gear 10t||2 block 15t||3 gears 20t||4 gear 26t||5th gear 29t|
|The height from the center of the buffer seat to the rail surface|
|CDH-C||CDH-C-type||CDH-CC type||CDH-CQ type|
|850 ± 10mm||720 ± 10mm||660 ± 10mm||660 ± 10mm|
|Total horizontal resistance when sliding|
|1st block 10t 2nd block 15t||3 blocks 20t 4 blocks 26t||5th gear 29t|
|Total vehicle weight (t)||Speed (km / h)||Total resistance of vehicle stopper (t)|
The technical conditions of the line should meet the engineering standards, and the gauge is 1435 + 6-2;
The car stopper should be installed at the last section of the rail at the end of the line, close to the rail joint and without a fish plate. The distance between the car stopper and the end of the line should be greater.
? Put the left and right arms on the basic rail, and connect them to the base with the arm pin.
? Raise the support arm, and place the spring seat, leaf spring and bearing seat in this order on the basic rail under the hoof.
? Use the brake rail to clamp the shoe block, and also clamp the rail head of the basic rail, and then use three bolts to bring the brake rail on. Note that the two bolts on the outside must pass through the support frame, and the seat should be in the middle of the pressure hole.
? Use the front and rear beams and the upper and lower oblique beams to connect the four feet under the two arms. The overlapping form is shown in the figure. After the initial installation is completed, tighten the bolts.
? The installation of the booster is to place the spring seat, the leaf spring and the bearing in order on the basic rail, and then sandwich it with the two booster brake rails, and also clamp the rail head of the basic rail. Bolts to tighten the brake rail. The first pair of boosters is 100 mm from the main body frame, and the second pair of boosters is 80 mm from the first pair, parallel to each other, and the error is not more than 2 mm.
? Press each spring plate with a presser: insert the U-shaped pressurized quick insert into the neutral position on both sides of the seat, and the head of the pressurized screw installed on the central nut of the presser is aligned with the pressurized block and hung on both sides The bottom plate of the pressure rail is hooked on the bottom plate of the basic rail. Tighten it with a nut. Use an iron rod with a length of about 1.5 meters to turn the pressure screw and drive the wedge iron between the bearing and the plate spring. 0.05 mm.
?Install the sign on the support.
?After each installation, position marks should be painted on the rail waist to facilitate daily inspection of the car stopper for damage.
The car stopper should be restored to its original position in time after being hit. You can take out the wedge iron first, push the main body frame and booster back to the original position, and then re-tighten and pressurize according to the above method.
Keep the car stopper in good working condition and check it in turn every month to confirm if there is any displacement, deformation and loose screws, and immediately deal with it if there is something abnormal.
Attention should be paid to clear the obstacles on the rail surface in the sliding direction of the vehicle stopper, and handle the super-high road studs and sleeper bolts.
Apply anti-rust paint to the car stopper every two years.
Call the Group Sales Specialist Hotline
11 North Kaiyuan Road, Jining High-tech Zone, Shandong
Scan, mobile access
China Coal Official WeChat
China Coal Official WeChat Mini Program